中電網移動|移動中電網
 
 
中電網移動|移動中電網|高清图滚动区

IDT 5X1503带嵌入晶振MicroClock可编時鍾發生器解決方案

IDT公司的5X1503系列是小型尺寸的可编時鍾發生器,采用1 PLL + DCO架构,设计有嵌入晶体振荡器,是OTP可编程,允许有多达3个单独频率输出.5X1503内置了独特的特性如主动节能(PPS)和低功耗DCO,以支持系统日期/时间运行32.768kHz时钟.动态频率控制(DFC)通过外部要求支持四个不同PLL频率间的动态变化,从而降低频率过冲与下冲(ORT).5X1403S还支持广谱时钟以降低EMI.器件内部OTP存储器允许用户存储多达4个单独配置,不用编程在加电时就能加载.也可通过I2C接口再次编程.5X1503支持三种LVCMOS类型输出.两种输出有可编幅度(1V, 1.1V, 1.2V和1.8V).支持用于系统RTC参考时钟32.768kHz耗电小于1.5μA.工作电压1.8V,2 × 2 mm 10-VFQFPN封装.主要用在智能设备(SmartDevice),手持設備,可穿戴设备和手持消費類電子设备.本文介绍了5X1503主要特性和输出特性,主要指标,框图及开发板特性包括开发板套件插座板和评估板电路图以及相关外形图.

The 5X1503 is a series of small form factor programmable clockgenerators intended for low-power, consumer, battery poweredapplications, wearable and smart devices.

The device is a 1 PLL + DCO architecture design with oneembedded crystal. The device is OTP programmable, allowing forup to 3 unique frequency outputs. The 5X1503 has built-in uniquefeatures such as Proactive Power Saving (PPS) and a low powerDCO to support system date/time keeping clock at 32.768kHz.

Dynamic Frequency Control (DFC) supports dynamically changingbetween four different PLL frequencies via external requests withcontrolled frequency changes, reducing frequency overshoot andundershoot (ORT). The 5X1503S device can also support aspread clock for EMI reduction.

An internal OTP memory allows the user to store up to fourindependent configurations that can be loaded on power-upwithout programming. It can then be reprogrammed again throughthe I2C interface.

The 5X1503 supports three LVCMOS type outputs. Two outputshave programmable amplitude. A low-power 32.768kHz clock issupported with only less than 1.5μA current consumption forsystem RTC reference clock needs.

5X1503主要特性:

▪ Proactive Power Saving (PPS) features save power during theend device power-down mode
▪ Dynamic Frequency Control (DFC) feature allows programmingup to 4 difference frequencies that switch dynamically
▪ Programmable output clock amplitude (1V,1.1V,1.2V and1.8V) to support low swing clock requirement
▪ Dedicated 32kHz output with 6 clock amplitude options(5X1503L)
▪ Integrated crystal; no external input source requirement
▪ Configurable through I2C or OTP programming
▪ Spread spectrum clock support (5X1503S)
▪ 1.8V operating supply voltage
▪ 2 × 2 mm 10-VFQFPN package

5X1503輸出特性:

▪ 3 LVCMOS outputs, 1MHz–100MHz or 32.768kHz
▪ Low-power 32.768kHz clock supported

5X1503主要指標:

▪ Output cycle-cycle jitter: 50ps (typ)
▪ Low power-on fully active mode: 2mA (typ)
▪ Low-power 32.768kHz < 1.0μA (5X1503L)

5X1503典型應用:

▪ SmartDevice
▪ Handheld
▪ Wearable applications
▪ Portable Consumer applications

圖1.5X1503框圖

開發板5X1503

The MicroClock development kit is designed to support the 5X1503/5L1503 devices. It provides a convenient way of verifying, configuringand programming the blank parts for MicroClock devices 5X1503 and 5L1503. The IDT Timing Commander™ GUI supports to thedevices for configuration and frequency validation on a socket board through a USB programmer board in USB interface. Thedevelopment kit support programming to MicroClock blank parts either placed into a socket of the board or the blank device soldered onevaluation boards as additional extension boards.

圖2.插座板概述圖(5X1503板插座關閉時在下面)
插座板數字描述:



圖3.5X1503開發板套件圖

圖4.5X1503開發板套件插座板電路圖

圖5.5X1503開發板套件評估板電路圖

圖6.5X1503插座板(板上配有用于評估52MHz晶體)

圖7.5L1503插座板(板上配有用于評估25MHz晶體)

圖8.5X1503插座板(板上沒有晶體)

圖9.5L1503插座板(板上配有25MHz晶體)
詳情請見:
https://www.idt.com/document/dst/5x1503-datasheet
和https://www.idt.com/document/mau/5x1503-family-development-kit-user-guide
以及https://www.idt.com/document/sch/5x1503-5l1503-reference-schematic
IDT_5X1503-5L1503-Ref-Schematic_SCH_20190724.pdf
IDT_5X1503_DST_20190619.pdf
IDT_5x1503-Family-DevKit-UG_MAU_20190724.pdf

猜你喜歡
中電網移動|移動中電網|频道导航区